How to sync dogtra 1900s collar 

How to sync dogtra 1900s collar 

Wondering how to sync dogtra 1900s collar? This is the right guide for you. Am going to guide you on how to reset dogtra collar and troubleshooting various problem that you may encounter while training.

There two models of dogtra 1900s remote training collars i.e.

  • One dog system-This is a dogtra remote capable of only handling one dog collar. It means you can only train one dog at one time.
  • Two-dog system-Dogtra remote that is two-dog system is capable of training two dogs at the same time.

The way you synchronize one dog transmitter is different when you are using a two-dog system. So let look at how to sync dogtra collar.

How to sync dogtra collar.

Let start with non-expandable system

One dog system (Non-expandable)

D the following steps to synchronize a one-dog dogtra 1900s system.

  1. Switch on the remote by pressing the ON and OFF button. It is also important to note that there are remotes that do not have on and off buttons.
  2. Set the shock stimulation level to zero.
  3. Check for a red dot on the transmitter and collar receiver. Bring the two dots together for at least 5 seconds.dogtra one dog system
  4. Wait until you see LED light on the receiver has started blinking in green color.
  5. Separate the two red dots on the remote and receiver. Within the 5 seconds of separation, press simultaneously the nick and constant buttons on the remote for at least 3 seconds.dogtra nick and constant buttons
  6. Wait until the green blink on the collar has slowed blinking.
  7. Finally, when everything is okay, the LED light on the receiver will start blinking only every four seconds.

Two dog system (Expandable)

  1. Switch on the remote by pressing ON and OFF button. It is also important to note that there are remotes that do not have on and off buttons.
  2. Set the shock stimulation level to zero.
  3. Push up the toggle button to synchronize black collar or push down to synchronize the orange collar.dogtra Two dog system (Expandable)
  4. Check for a red dot on the transmitter and collar receiver. Bring the two dots together for at least 5 seconds.
  5. Wait until you see LED light on the receiver has started blinking in green color.
  6. Wait for 5 seconds after moving the two dots apart then press the black and orange button at the same time for at least 3 seconds.
  7. Wait until the green blinks at a slow pace.

Frequently asked questions

Below are some of the frequently asked questions about dogtra collar systems that can as well apply to other ecollar models

How to reset dogtra collar

If you have purchased a dogtra replacement transmitter or collar receiver, you may need to reset it so that it can work with your existing remote or receiver.

To reset your dogtra collar, below is the procedure.

  1. Press off button to switch off the collar.
  2. Press the on and off button. The collar light will turn on then it will turn off after fourth or five seconds.
  3. In case you release on/off button early, the collar receiver will start flashing. If this happens it means you will have to start the process again repeating step one.
  4. Wait until collar light has gone off then you can release the on and off button.
  5. Locate the Upper button then press then hold on the remote, and wait until the collar receiver light indicator has flashed 5 times. You are also required to hold the two devices 2-3 feet apart while doing this.
  6. Keep on checking on collar indicator light and if it flashes five times, it means the receiver has been reset and normal flashing should resume.
  7. In case the indicator light fails to flash, five times you will have to repeat the whole process from step 1.

Note

Some collars have a reset button. If yours has the reset button, you do not need to follow the above procedure. All you have to do is press the reset button and collar will reset itself automatically.

Otherwise, you can also try to turn collar off. Then press and hold the on button until indicator light burns solid. The collar will go off then you can release the on button.

Related Content :Dogtra shock collar not working

Conclusion

When you purchase a new dogtra collar they always come with a manual. Referring to your dogtra 1900s manual can be helpful since it will guide you on how to perform various tasks.

 

Resources:

https://www.dogtra.com/cache/DOC54_20150115_CS_Gudide_3500NCP.pdf?20160224022715

Follow my blog with Bloglovin

Leave a Reply

Your email address will not be published. Required fields are marked *

E-collarE-collar